Frequency: 54 to 250Hz 

Enclosure Type: Bandpass Horn

Size: 670x600x750mm

Recommended Drivers: SD18 or C18-650EL

Plan:alt

ES18-BPH

Designer: Stipe Ercegovic (This email address is being protected from spambots. You need JavaScript enabled to view it.)

Log in to comment

rubdubsound replied the topic:
7 years 8 months ago
got my hand on 2 B&C tbx100 thinking about trying to build 2 of these ES18BPH cabinets will they work good in them
m0gsia replied the topic:
8 years 7 months ago
Does anyone have any feedback on RCF LF18G401 in these cabs? Thanks Chris
Ross_161 replied the topic:
9 years 5 months ago
How many sheets are needed to make 2 cabs? And where is best to place the handles on this cab?

Many thanks :D
Lofobia replied the topic:
9 years 9 months ago
Budget is around 1500SEK (114£) /Element


But still wonder is i can use the EBP to find suitable elements?
bee replied the topic:
9 years 9 months ago
whats your budget per driver, I stock or can get bms, pd, fane, celestion, eminence, to name a few.. based on your budget im happy to recommend a driver...
Lofobia replied the topic:
9 years 9 months ago
I´m looking for cheaper drivers for this cab.

Can i search drivers via EBP?

The SD18 has a EBP of 126,9
and C18-650EL has a EBP of 88.5. (FS/Qts=EBP)

If i find drivers with EBP close to those EBP values, would it work OK in the ES18-BPH?
bee replied the topic:
9 years 11 months ago
reply in other thread.... yes the mk2 has a bigger wider magnet... so wont fit in the es18, the only option I see is for you to make a shim (spacer) for the baffle to bring the driver back into the chamber.
nitrousoutlaw replied the topic:
9 years 11 months ago
Did the dimensions for the c18-650el v2 change from the original? The speaker magnet hits the rear and bottom panel not letting it sit flush. I triple checked my measurements and they're good.
Lofobia replied the topic:
9 years 11 months ago
Is there a cheaper driver thats work well in this horn?

I can´t afford 4 SD18 & c18... :(
bjm362 replied the topic:
10 years 3 weeks ago
I wasn't trying to participate in the discussion about this particular plan, but did want to look at it. When I tried to use the link posted I got this:

"This Connection is Untrusted

You have asked Firefox to connect securely to www.freespeakerplans.com , but we can't confirm that your connection is secure.

Normally, when you try to connect securely, sites will present trusted identification to prove that you are going to the right place. However, this site's identity can't be verified.
What Should I Do?

If you usually connect to this site without problems, this error could mean that someone is trying to impersonate the site, and you shouldn't continue."


I normally do not see this error, but started to presume it was safe because it is here at Freespeakerplans. It then gave me another warning when I attempted to allow it and proceed:

"If you understand what's going on, you can tell Firefox to start trusting this site's identification. Even if you trust the site, this error could mean that someone is tampering with your connection.

Don't add an exception unless you know there's a good reason why this site doesn't use trusted identification."


I then decided to wait until I mentioned this to you guys before proceeding at all. This may be normal due to how it is hosted....but then I have looked at a lot of plans here and not encountered this. I wasn't sure how to approach it but did feel it would be irresponsible not to mention it..even if it turns out to be something laughable I should have known about! In this case I would rather even be laughed at then not to have informed the group when I should have!
c-audiofreak replied the topic:
10 years 3 weeks ago
hi all i want to build these as kicks above my x1 subs but need to cut my suit according to my cloth so was wondering if i could use either the emminence sigma pro delta pro or omega pro in this cab aiming to build a pair to begin with then another pair later along withnother pair of x1 and two pairs of MT122 will it work?
ganjafarmers s.s. replied the topic:
10 years 1 month ago
hi everybody,
do you think a pd 1850 would work as well? i want to use them as kick cabinet.
i don't know how can the bottom braces can fix. i mean that them crash with panel B. how did you overcome this?
thanks
anjmoor replied the topic:
10 years 2 months ago
Yes you will need to reverse the polarity as your speaker will need to fire backwards
PrettyHard replied the topic:
10 years 3 months ago
In using this cab should i invert the polarity?
Vaibhavdj141996 replied the topic:
10 years 3 months ago
Can RCF LF18G401 is suitable for it if magnet side put in the chamber?
pairoj replied the topic:
11 years 1 week ago
Thank you
bitzo replied the topic:
12 years 10 months ago
big brace distance from baffle in akabak sintax

sin(rad(40))*(paneljheight-(1/sin(rad(40))*woodthickness+7.7e-2+bigbraceheight+woodthickness))
_natty_ replied the topic:
12 years 10 months ago
no bitzo!
i'd like to say how deep the speaker basket could be!
bitzo replied the topic:
12 years 11 months ago
encreasing depth without any other mods means enlarging compression chamber and throat... so means encreasing low end or gain some db on low bandwith part and may be loose high end extension. Mr. Stipe cabs make always discuss about them, I like it. smiley20
_natty_ replied the topic:
12 years 11 months ago
hiany one know how deep could be the speaker at maximum?
tamuks replied the topic:
12 years 11 months ago
does anyone have plans for 21 inch speakers on this cab
staiper replied the topic:
13 years 2 months ago

levyte357 wrote: Can anyone "guess-etimate" the response of this cab, if depth is reduced to 636mmm?

I expect shortening horn, and reducing chamber will reduce low end response, will it still reach downto usable 65hz?

More importantly, will upper response be extended?


Yes for pure kick bin that can be done..
Sacrifice is a bit shorter horn which will take away bit of low extension but 65 Hz will still be in good efficiency range.

I have already made slight simple modification for Electrikal to make "face" of cabinet 636 x 636 mm which will make it more flexible for stacking in various combination's with HOG-s and other 636mm wide scoops.

now I see ..according to some inditions and informations from Sherlock Holmes you already know that smiley2


.. Have to make some sims to see what upper response with trimmed depth from 750 to ~670 will do.. But that can give us just idea as final "character" and "honk/no honk" in delicate low vocal area is impossible to simulate.
In this situation (when you look for better high cutoff) additional Neilpoints modification ( forum.speakerplans.com/forum_posts.asp?T...title=es18bph#470523 ) may be good idea to do.
saul replied the topic:
13 years 2 months ago
thing is with 3 or 4 next to each other, the whole lot actually gets deeper than 668mm
levyte357 replied the topic:
13 years 2 months ago

saul wrote: if you draw a vertical line around 110mm from the front of the cab, yeah i guess lose mouth area horn length and chamber.

horn length is currently 75cm in theory - this is only 110hz @ 1/4 wave

so the rest is the chambers?

just wondering though, why?


Why reducing depth?

Cube shape kick.. Aesthetics.

But just realised MT121 is approx 668mm deep, so "my" ES18 would have to be at least this as well.
saul replied the topic:
13 years 2 months ago
if you draw a vertical line around 110mm from the front of the cab, yeah i guess lose mouth area horn length and chamber.

horn length is currently 75cm in theory - this is only 110hz @ 1/4 wave

so the rest is the chambers?

just wondering though, why?